Schilke Trumpet Mouthpiece
Schilke Mouthpiece Numbering Systems
The Schilke method
of mouthpiece labeling has been designed to assist the student, teacher, amateur and professional in selecting a mouthpiece
to meet the needs of the player. All mouthpieces come with standard rim shapes, cup volumes, and backbores unless shown otherwise
on the mouthpieces. This method enables the player to know the characteristics of their trumpet mouthpiece.
Example:
a trumpet mouthpiece using this method might be called 9C3c
Using this example, 9 refers to the CUP DIAMETER Smallest
numbers have smallest diameters C E. Large C refers to the CUP VOLUME A. Small Cup B. Medium-small C. Standard (medium size)
D. Medium-large E. Large 3 refers to the RIM CONTOUR 1 Rounded 2 Semi-rounded 3 Standard 4 Semi-flat 5 Only slightly rounded
c refers to the BACKBORE a. Tight b. Straight c. Standard d. Slightly curved out e. Large When a Schilke mouthpiece has a
standard backbore, rim and cup, only the cup diameter (first number) is shown on the mouthpiece. In the example above only
the #9 is necessary to identify the mouthpiece because the C is the standard cup volume, 3 is the standard rim, and c is the
standard backbore. Whenever measurements differ from the standard sizes the alterations are shown on the mouthpiece.
CUP
DIAMETER (First number in label)
Most trumpet and cornet mouthpieces have a cap diameter that falls between .600"
and . 725". Nos. 1 to 25 in the Schilke system represent sections of .005" each between these two measurements. Cup diameters
for mouthpieces other than trumpet and cornet are relative to each other with the smallest numbers representing the smallest
diameters
CUP VOLUME (First letter in label)
In general the deep cup mouthpieces produce the darkest sounds.
In reverse the shallow cup mouthpieces produce the brightest sounds and also aid in the production of the high register. The
Schilke "C" cup is a comprise which offers both full tone and ease of production. In switching from one instrument to another
i.e., Bb trumpet to D trumpet, it is usually good to use a mouth piece that is .025" shallower in the cup volume with all
other dimensions remaining the same. The higher the instrument is, the shallower the cup should be. A player who needs primarily
a good range without sacrificing much tone can consider a hollow mouthpiece with a widened 2nd cup. The shallow 1st cup affords
support in the top register and the widened 2nd cup allows a full tone.
RIM CONTOUR (Second number in label)
The
#3 Schilke rim has the feel that most players prefer in a rim. It has flat enough contour to distribute the slight pressure
needed to provide an air seal but is rounded slightly to offer increased flexibility. Generally a rounder rim will allow greater
flexibility but sometimes tires the player sooner. A flat rim often feels the most comfortable but tends to hold the lips
in a fixed position, thereby reducing flexibility.
BACKBORE (Last letter in label)
Schilke mouthpieces all
come with standard backbores (letter C) which permit the maximum in tone and range. Other backbores are available (Letters
a, b, d, e) which might suit particular needs of players. The tighter backbores tend to make the sound more brilliant while
the larger backbores tend to make the sound more mellow. Occasionally a change in backbores will cause an alteration in intonation
which often can correct faulty intonation on an instrument.
THE FIT OF THE MOUTHPIECE
The shank of every
brass mouthpiece when in the instrument should touch the end of the mouthpipe to insure an even taper from the backbore of
the mouthpiece to the inside of the mouthpipe. Dirt inside the throat or backbore of a mouthpiece can greatly alter the intonation
of the instrument on which it is used. Mouthpieces can only be kept clean with a mouthpiece brush used every week
Save BIG when you buy today!
