Solid bass sound with tight lows.

The Eminence Legend BP102 10" Bass Speaker delivers rich bass tone with a lot of punch. Recommended for professional bass guitar applications in sealed or vented enclosures. The replacement speaker works well in single or multi-driver designs.

Use the Eminence Legend BP102 as a direct replacement speaker in the Ampeg SVT-810E, the Kustom Groove 4120, the Gallien-Krueger 4120 SBX, the Ashdown MAG 410T & MAG810T, and the Basson B410B speaker cabinets. Eminence recommends the Legend BP102 as a direct replacement in the Kustom Groove 310C, the Ampeg BA210SP, the Peavey Bam 210 combo amps.

Eminence Legend BP102 10" 200W Bass Speaker Features:

• Rich bass tone with good punch
• Tight low-end sound
• Recommended for sealed or vented enclosures
• Works well in single or multi-driver cabs

Put this Eminence bass speaker in the cart and make your bass cab sound better than new.

Eminence Legend BP102 10" 200W Bass Speaker Specifications:

• Nominal Basket Diameter: 10", 254mm
• Nominal Impedance*: 8 ohms
• Power Rating**: 200W
• Resonance: 35Hz
• Usable Frequency Range: 44Hz-4kHz
• Sensitivity***: 92
• Magnet Weight: 38 oz.
• Gap Height: 0.312", 7.92mm
• Voice Coil Diameter : 2", 50.8mm
  
  Resonant Frequency (fs): 35Hz
• DC Resistance (Re): 5.59
• Coil Inductance (Le): 0.83mH
• Mechanical Q (Qms): 5.36
• Electromagnetic Q (Qes): 0.47
• Total Q (Qts): 0.43
• Compliance Equivalent Volume (Vas): 91.2 liters / 3.2 cu. ft.
• Peak Diaphragm Displacement Volume (Vd): 207cc
• Mechanical Compliance of Suspension (Cms): 0.54mm/N
• BL Product (BL): 10.0 T-M
• Diaphragm Mass inc. Airload (Mms): 38 grams
• Efficiency Bandwidth Product (EBP): 75
• Maximum Linear Excursion (Xmax): 6.2mm
• Surface Area of Cone (Sd): 334.5 cm2
• Maximum Mechanical Limit (Xlim): 10.0mm
  
  Mounting Information
• Recommended Enclosure Volume
• Sealed: 14-28 liters/ 0.5-1 cu.ft.
• Vented: 25.5-62 liters/ 0.9-2.2 cu.ft.
• Overall Diameter: 10.08", 256.1mm
• Baffle Hole Diameter: 9.05", 229.7mm
• Front Sealing Gasket: fitted as standard
• Rear Sealing Gasket:
• Mounting Holes Diameter: 0.25", 6.4mm
• Mounting Holes B.C.D.: 9.66", 245.4mm
• Depth: 4.25", 108mm
• Net Weight: 8.9 lb., 4 kg
• Shipping Weight: 9.1 lbs., 4.1 kg
  
  Materials of Construction
• Copper voice coil
• Polyimide former
• Ferrite magnet
• Non-vented core
• Pressed steel basket
• Paper Cone
• Cloth cone edge
• Zurette dust cap
  
  *Please inquire about alternative impedances.
• **Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, non-temperature controlled environment.
• ***The average output across the usable frequency range when applying 1W/1M into the nominal impedance. Ie: 2.83V/8ohms, 4V/16ohms.
• Eminence response curves are measured under the following conditions: All speakers are tested at 1w/1m using a variety of test set-ups for the appropriate impedance | LMS using 0.25" supplied microphone (software
• calibrated) mounted 1m from wall/baffle | 2ft. X 2ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction | Hafler P1500 Trans-Nova amplifier | 2700 cu.ft. chamber with
• fiberglass on all six surfaces (three with custom-made wedges)