Solid-state preamp and analog power.

The Markbass Little Mark 250 bass amp head is a high-quality bass amplifier with a solid-state preamp and an analog power amp. The Little Mark 250 delivers 250W of power into a 4 ohm cabinet, or 150W into an 8 ohm cabinet. This Little Mark has a 4-band EQ, Markbass' VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters, as well as both Gain and Master volume controls. The front panel accepts both a passive or active bass 1/4" input, as well as a balanced XLR input for acoustic bass pickup systems or a microphone. On the rear panel you'll find a Neutrik Speakon combo jack output that accepts both Speakon or 1/4" speaker cable as well as a second 1/4" speaker out jack. You'll also find a balanced XLR out, unbalanced tuner out so you can tune as you play without passing your signal through pedals, and a Send and Return Effect loop which saves you from losing your signal if one of your pedals dies or a cable in the chain gives out.

Markbass Little Mark 250 Bass Amp Head Features:

• Solid state preamp analog bass head
• Provides 150W RMS at 8 ohms, 250W RMS at 4 ohms
• 1/4" input jack works with active or passive basses
• Gain and Master volume controls
• Clip warning light
• EQ includes controls for Low, Mid Frequency Low, High Frequency Low, and High
• VLE (Vintage Loudspeaker Emulator) and VPF (Variable Pre-shape Filter) filters
• Neutrik Speakon Combo out jacks for use with 1/4" or Speakon speaker cables
• Balanced XLR out
• Ground lift switch to eliminate hum
• Tuner out sends unbalanced signal sent to a tuner, amp or recording equipment not needing a balanced signal
• Send and Return Effect ensures main signal continues even if something dies in your effects chain
• Dual-sided fiberglass PC boards with lined perforations for high-quality solder connections
• Surface-mount components are silicon-sealed to isolate vibrations
• Computer-grade pre-assembled ribbon connector cable harnesses and ribbons for noise-free operation
• Integrated threaded posts for easy assembly/disassembly and added durability
• Rigid 2mm thick aluminium chassis for a long-lasting finish

Don't let the size fool ya, this little combo head packs a nice punch. Order today!

Markbass Little Mark 250 Bass Amp Head Specifications:

• Power
• Input impedance: 500Kohm, max. voltage: 15 Vpp
• Balanced input impedance: 22Kohm, max. voltage: 25 Vpp
  
  Effect Return impedance: 22Kohm, max. voltage: 25 Vpp
• Output Power: 150W RMS at 8 ohms, 250W RMS at 4 ohms
• Voltage is factory preset for the U.S.
  
  Controls
• GAIN: —80dB to +23dB range
• GROUND LIFT: Switch on rear panel
• MASTER VOLUME
  
  Equalization
• LOW
• Center frequency: 40Hz; level ±16dB
• LOW-MID
• Semi-parametric: frequency 360Hz, level ±16dB
• HIGH-MID
• Semi-parametric: frequency 800Hz, level ±16dB
• HIGH
• Semi-parametric: 10kHz shelf; level ±16dB
• VPF (Variable Pre-shape Filter)
• Center frequency: 380Hz (cut)
• VLE (Vintage Loudspeaker Emulator)
• 250Hz — 20kHz cut
  
  Outputs
• EFFECT SEND
• Unbalanced, max. voltage 20 Vpp (pre-EQ)
• TUNER OUT
• Unbalanced, max. voltage 25 Vpp
• LINE OUT
• Balanced XLR, max. voltage 10 Vpp
• SPEAKER OUT
• Speakon, 1/4"
  
  Other
• Dimensions: 10.87"(W) x 2.8"(H) x 10.1"(D)
• Weight: 5.73 lbs.